Samsung Galaxy J3 2016 (samsung-j3xnlte)
| This device is based on the Spreadtrum SC9830
. See the SoC page for common tips, guides and troubleshooting steps |
| This device has been archived. This means that it no longer appears in pmbootstrap and is likely broken. It can still be selected in pmbootstrap init by typing in the vendor and codename, but you will have to build the kernel package manually. |
|
Galaxy J3 (2016) Running SXMO | |
| Manufacturer | Samsung |
|---|---|
| Name | Galaxy J3 2016 |
| Codename | samsung-j3xnlte |
| Model | SM-J320FN |
| Released | 2016 |
| Type | handset |
| Hardware | |
| Chipset | Spreadtrum SC9830I |
| CPU | 4 x 1.5 GHz Cortex-A7 |
| GPU | Mali-400 MP |
| Display | 720x1280 AMOLED |
| Storage | 8 GB |
| Memory | 1.5 GB |
| Architecture | armv7 |
| Software | |
Original software The software and version the device was shipped with. |
Android (TouchWiz) 5.1.1 |
Extended version The most recent supported version from the manufacturer. |
Android (TouchWiz) |
| Optional software | Android (LineageOS) (Unofficial) |
| Nura | |
| Category | archived |
Mainline Instead of a Linux kernel fork, it is possible to run (Close to) Mainline. |
no |
Nura kernel The kernel version that runs on the device's port. |
3.10.100 |
| Device package |
|
| Kernel package |
|
Initial MR Initial merge request. |
pmaports!653 |
Flashing Whether it is possible to flash the device with pmbootstrap flasher. |
Works
|
|---|---|
USB Networking After connecting the device with USB to your PC, you can connect to it via telnet (initramfs) or SSH (booted system). |
Works
|
SD card Also includes other external storage cards. |
Partial
|
Battery Whether charging and battery level reporting work. |
Works
|
Screen Whether the display works; ideally with sleep mode and brightness control. |
Works
|
Touchscreen |
Works
|
| Multimedia | |
3D Acceleration |
Broken
|
Audio Audio playback, microphone, headset and buttons. |
Works
|
Camera |
Broken
|
| Connectivity | |
Wi-Fi |
Broken
|
Bluetooth |
Broken
|
GPS |
Broken
|
NFC Near Field Communication |
Untested
|
| Modem | |
Calls |
Broken
|
SMS |
Broken
|
Mobile data |
Broken
|
| Miscellaneous | |
FDE Full disk encryption and unlocking with unl0kr. |
Broken
|
USB OTG USB On-The-Go or USB-C Role switching. |
Works
|
| Sensors | |
Accelerometer Handles automatic screen rotation in many interfaces. |
Broken
|
| Note: This page is about Spreadtrum SC9830 variants of Samsung Galaxy J3. |
The Samsung Galaxy J3 (2016), also called Samsung Galaxy J3 6, is an Android smartphone which was developed by Samsung Electronics and was released on 15 January 2016.
Contributors
- Ster Please contact me on Matrix if you are at any step of the process, either by mentioning my username
@sterrss:matrix.orgor simply message me directly, I'd love to hear any success, failures, difficulties. I'm not necessarily going to be able to help you, since I've still got lots to learn but it'd be nice to chat. - 37nx Contact me at matrix
@121212121212_:matrix.orgif you have any questions i will try to help you. im barely online now i might try to help you anyways in any possible way
Users owning this device
- 0d (Notes: SM-J320FN)
- 37nx (Notes: one working now.....)
- Alone-Wolf13785 (Notes: Currently on lineage os but wanna try pmOS)
- Andrisas
- BruninTech (Notes: Running Android?, 8GB, Broken display, no battery)
- Flocreeperbytin (Notes: two of em.... technically one is just a motherboard the other is complete)
- Kcxt (Notes: x2 Borked)
- Kolja (Notes: I have J320F, I've tried running the J320FN version but it didn't work.)
- LegoLivesMatter (Notes: Running LineageOS 14.1)
- Little-miss-synth (Notes: runs lineageOS may try postmarketOS on it at some point)
- MettleSphee
- Mtek89 (Notes: Stock Android, broken screen, mother's phone)
- Nomz
- Owen
- Paulth67 (Notes: J320FN)
- Ptesarik (Notes: free to develop)
- Shadowsvanish (Notes: J320M variant, missing display)
- Speedyes (Notes: SM-J320F, LineageOS)
- Stelle (Notes: no battery, powered by a USB cable, runs pmOS edge kernel 3.10)
- Ster (Notes: Ported to postmarketOS)
- UltrasonicMadness (Notes: 3×SM-J320FN, 2×SM-J320F - all but one of the FNs have varying degrees of screen burn)
- W4trmelon (Notes: working !)
- ZBookCMD (Notes: Radical Experience; Reserve)
- Zillion (Notes: J320F, Currently running dotOS)
Initial comments
Note that there are different models of the Samsung Galaxy J3. To see which one you have, if you still have the original recovery image on your device, power it off and then hold down the home button, power button and volume up button. See at the top of the phone's screen for the model code. If it's J320FN(string of characters) you're probably good to go. If yours is J320F it will probably be very similar to port.
Alternatively, simply remove the back cover and battery. The sticker underneath should read: MODEL: SM-J320FN.
WARNING: Logout / delete all of the accounts (especially Google ones) in Android first, before you wiping out or flashing Nura to partition system. |
Special boot modes
- Download/Odin Mode: With the device powered off, hold , and while connecting the device to a computer with a USB cable. A warning screen will appear: click to enter Download Mode and run Heimdall commands.
Installation
Flashing works since pmaports!4315, so the image can be installed normally.
you can also flash it via zip from recovery pmbootstrap install --android-recovery-zip and then running pmbootstrap export
TWRP
Firstly, download TWRP from the XDA developers page. The download is in the section labelled "Attachments".
Use Heimdall to flash recovery.img to the recovery partition of your device:
- Put it in Download Mode (see above)
- Connect to computer
- Run
heimdall detectto see if heimdall can see it. - Run
heimdall flash --RECOVERY recovery.img, making sure you are in the directory withrecovery.img
| Information in this section may be outdated. |
Disconnect the cable when you turn the device off. The device freezes on the charging splash screen if it's not disconnected also trying to charge the phone will boot it.
Mainlining
| Hardware type | Chip | Mainline status | Notes |
|---|---|---|---|
| WiFi chip | Spreadtrum SC2331 | N | |
| Charging IC | Silicon Mitus SM5701 | N | |
| Fuel gauge | Spreadtrum SC27x3 | P | SC27xx driver present, maybe it can be used |
| GNSS | Broadcom BCM47250 | N | |
| NFC | NXP PN547 | P | PN544 driver present |
| Proximity sensor | Capella Microsystems CM36672P | P | Capella CM36686 Driver Exists near identical maybe can be of use? |
| Accelerometer | Bosch BMA2xx | P | BMA220 driver present |
| Touchscreen | Imagis Technology IST3038C | Y | IST3038C driver present |
| Display panel | S6E8AA5X01 | N | |
| MUIC | Silicon Mitus SM5504 | Y | Fully supported |
| GPU | Mali-400 | Y | Mali Driver Available |
| Legend | |
|---|---|
| Y | Mainline driver present |
| P | Mainline driver for (possibly) similar IC present |
| N | Mainline driver not present at all |
SoC uses a custom hardware timer, which has to be ported before mainline can be booted.
Interfaces
| Some info might not be accurate. |
The only interfaces that work are LXQt and SXMO. Other interfaces such as Buffyboard don't work.
(maybe Display manager#CanGraphical issue could help?)
Installing apps
As Wi-Fi doesn't seem to work, you can install files through APK: sudo apk add htop-3.2.1-r1.apk or when using pmbootstrap choose packages to install there.
Sxmo support
A part of the deviceprofile error appears when booting, everything seems to work fine. Gestures, touch, and volume keys all work correctly. All menus work, as well as the st terminal, which just needs a smaller text size to fit certain programs. It is more usable than LXQt and has better keyboard support. (if Wi-Fi worked it would be better.)
External links
- Samsung Galaxy J3 (2016) on Wikipedia
- Device specifications on GSMArena
- Unofficial LineageOS port on XDA Developers on XDA Developers
- Unofficial TWRP 3.6.2-9.0 port on XDA Developers
- Kernel source code
- Someone's attempt to port Halium to samsung-j3xlte
- Drivers for Mali 400 and 450 from linux-sunxi